Shields : EtherMania, The store for network enthusiasts

Shields

In this area you can find Shields for Arduino.
Shields are add-on boards that could enhance the Arduino's capabilities adding sophisticated Input/Output stages.

Add to compare
up to 4 items

1 2 Next >>

Displaying 1 to 12 (of 18 products)

Product Image	Quantity-	Item Name	Price
Add to compare	8	4 Channels High Power LED driver shield On stock NOW! This shield is able to drive 4 High Power LED strings. Each channel provides 350mA and is current limited. That means you can connect series more than one LED without care about series resistors. The four channels could be used to drive three RGB LED series and one White serie letting you able to generate complex colors and ambiences.If you're interested only in white light, the...	Contact Us
Add to compare	10	WeatherShield Pressure, Temperature, Humidity The WeatherShield is a unit that allows Arduino able to read Pressure, Temperature and Relative Humidity.The shield is equipped with three sensors and a PIC12F683 microcontroller programmed with a specific firmware that interfaces with Arduino through a two line bidirectional synchronous serial connection. The microcontroller is responsible for sampling and averaging the last 8 humidity, pressure...	Contact Us
Add to compare	8	RS485 Shield The RS485 serial bus is a standard mainly present on industrial buildings and home automation systems. Data are transmitted differentially on a single twisted pair resulting in a high noise immunity system able to transport data over hundreds of meters. This shield, compatible with Arduino and Netduino, allows the integration of that platforms with RS485 compliant equipments. This shield could...	Contact Us
Add to compare	1	GPS Shield with EM-406A SiRF III module Adding GPS to your Arduino has never been easier. Multiple GPS receivers attach easily to the shield, and with the example sketch (check below), you will be able to locate your exact position within a few meters. A connector for the popular EM-406 GPS receiver is populated on the board, and footprints for EM-408 and EB-85A connectors are also made available (connectors are not included and can be...	Contact Us
Add to compare	2	Xbee Shield The Xbee shield allows an Arduino board to communicate wirelessly using Zigbee. It is based on the Xbee module from MaxStream Series 2. The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight). It can be used as a serial/usb replacement or you can put it into a command mode and configure it for a variety of broadcast and mesh networking options. The shields...	Contact Us
Add to compare	3	Shield MEGA Proto PCB - Board It allows to mount and add your own circuits to Arduino MEGA board. PCB only.	Contact Us
Add to compare	1	Shield Proto PCB assemblata - Rev 3 It allows to mount and add your own circuits to Arduino boards and Arduino Rev 3 boards. PCB with SOLDERED HEADERs	Contact Us
Add to compare	128	15mm Strip 6 and 8 ways Pair of 1 8ways and 1 6ways Female/Male strip, very useful to be used for Arduino boards extensions. Dimensions: plastic body 8.5mm - pins 15mm - total 23.5mm.	Contact Us
Add to compare	3	Ardumoto - Moto Driver Shield This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board, includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. Control for motor attached to OUT1/2 is connected to digital line...	Contact Us
Add to compare	4	CAN Bus Shield This shield gives the Arduino CAN-Bus capability. It uses the Microchip MCP2515 CAN controller with MCP2551 CAN transceiver. CAN connection is via a standard 9-way sub-D for use with OBDII cable. Ideal for automative CAN application. The shield also has a uSD card holder, serial LCD connector and connector for an EM406 GPS module. Making this shield ideal for data logging application. Features...	Contact Us
Add to compare	1	Color LCD Shield The Color LCD Shield, recommended by and designed in partnership with an SFE customer, provides an easy method of connecting the popular Nokia 6100 LCD to your Arduino USB. The board comes as shown with the 128x128 mini color LCD, as well as a backlight driver circuit (boosts to 7V), and three momentary push-buttons (tied through a jumper to pins D3-5). The Nokia 6100 LCD is controlled through a...	Contact Us
Add to compare	2	MIDI Shield The MIDI Shield board gives your Arduino access to the powerful MIDI communication protocol, so you can control synthesizers, sequencers, and other musical devices. The MIDI protocol shares many similarities with standard asynchronous serial interfaces, so you can use the UART pins of your Arduino to send and receive MIDI's event messages. The MIDI Shield provides an opto-isolated MIDI-IN port...	Contact Us

Displaying 1 to 12 (of 18 products)